There are few things in the world that we take for granted more than toilets. We flush them a couple of times a day, and they just keep on going. But toilets do break down from time to time, and when they do it can be quite an inconvenience – but don’t worry! This article is here to help with all your toilet repair needs: what to look for in toilets before you buy one, how much does it cost to replace a toilet seat? What tools will I need? And so many other questions!
Problem: Toilet repair is a common problem for homeowners, and most people don’t know how to fix toilet problems.
Agitate: Most of us are not plumbers, so we need help when our toilets break down.
Solution: The Ultimate Guide to Toilet Repair will show you step by step instructions on how to fix your toilet at home. This guide covers everything from replacing worn parts like the fill valve and flapper, to fixing clogs with a plunger or snake. It even includes tips on preventing future issues with proper care and maintenance like keeping your tank clean and using only cold water in your toilet tank (no hot showers!).
How to Fix a Running Toilet
If your toilet is constantly running, it’s likely that the fill valve in the tank isn’t working correctly. To fix this problem, you’ll need to remove and replace the old fill valve with a new one.
Make sure that you shut off water supply to toilets before replacing any parts inside of them.
Turn off power for toilets by flipping breaker switch on main circuit panel if necessary. Remove lightbulbs or turncocks at base of toilets so they don’t come back on accidentally during repair time.
If there are two toilets next to each other, use pliers or channel locks to loosen nuts holding together connectors between pipes under floor level which connect toilets’ water supply lines above ground; then pull toilets apart.
Remove supply lines at toilets from top of tank with pliers or channel locks, and unscrew nuts holding them in place on underside of toilets’ tanks (usually two nuts). Let water drain out from pipes below floor level while doing this.
Disconnect fill line that brings water into the toilets’ tanks by pulling it off inside toilet’s tank where there is a plastic hose connecting it to metal pipe going down through bottom of tank; then unscrew nut holding sink stopper fixture on back side of tank over opening for toilets’ fill valve underneath toilet; pull up old fill valve using pry bar inserted through hole for overflow tube near base of toilets’ upper cabinets if necessary. Replace new part without forgetting about pipe running through toilets’ overflow tube hole.
Screw new fill valve into place on back of toilets tank and tighten nut using pry bar to prevent leak; reattach metal pipe that had been detached in step !!! above by pushing it down through toilets refill line opening inside toilet’s tank, then screwing nuts holding it in place at base of toilets’ tanks (usually two screws). Make sure supply lines are tightly screwed onto tops of toilets after the job is done.
Turn power for toilets back on if necessary before replacing lightbulbs or turncocks at bases of toilets so they come back on automatically again when you’re done with repairs. Replace cover over top of toilets and flush them both a couple times to verify there are no leaks.
Turn toilets away from each other and reconnect connectors between toilet supply lines, as well as reattaching connections for toilets’ water supply line to the house’s main shutoff valve if necessary.
Make sure toilets are tight against the floor again by screwing nuts holding them in place on either side of toilets (usually two screws). Now turn pliers or channel locks so that they tighten these nuts together securely.
How to Fix a Leaky Toilet
A leaky toilet can be a major expense, and nobody wants to deal with the inconvenience of one. Fortunately there are plenty of ways you can fix it yourself without having to call in an expensive plumber. Here is a list of some fixes that should work for most toilets:
Clean out any debris from around your tank or bowl – A clog could cause water to escape through the overflow pipe
Remove all foreign objects from inside your toilet – Hairballs, cups, toys etc., anything circling in your toilets drain will prevent proper flow and lead to leaks!
Replace old flapper valve – This might seem like a no brainer but if you haven’t replaced this piece of rubber tubing since 1998 then maybe it’s time for a replacement
Replace old fill valve – Again, this might seem like an obvious fix but if your toilets water level is too high then the pressure may force leaks from around your tank or bowl. This repair should be easy to do yourself!
Make sure no foreign objects are blocking your toilet drain – If there is any debris in the trap under the toilet it can clog and cause a leaky toilets scenario. You’ll need some pliers and patience for this one as you have to remove all of that junk out by hand which could take awhile depending on how bad things look down there. Disgusting? Yes, but necessary sometimes!
How to Replace a Broken Flush Handle or Chain
You will need a pair of pliers and screwdriver to do this job
Replace the flush handle with one that is compatible for toilets.
The most common type are called lift chain handles. There are also ball chain, pull chain, or long push button lever style handles available on Amazon
Find the flush handle has a long chain is broken. Start by turning off the water, then remove the screws holding it in place with your screwdriver. Once you have removed them, use pliers to break apart and pull each side of the old one free from its hole
Remember to put a towel or something underneath so that when there’s a leak, all will be contained within this area and not get anything wet on top
Attach new install onto toilet tank lid using two screws provided with purchase
Turn back around water once installation is complete
Flush handle should be in place now and you are almost done!
Adjust the chain to suit your height preference for a comfortable flush. You can do this by either shortening or lengthening it, depending on which is needed. Make sure that there’s enough slack so that when toilets lever is down, the water flows properly. Once adjusted, use pliers to reattach both sides of old one free from its hole
Turn back around water once installation is complete.
How to Unclog Your Toilet
This is a guide on how to fix the clogging of toilets caused by hair, toilet paper or other materials that may be inside it such as food wrappings. It also discusses ways on what you can do before calling for help from your plumber so you don’t have to spend more than necessary just because something occurred in your bathroom.
– Make sure there’s no water left inside the bowl after flushing
– Unplug any nearby sinks – this will create enough suction for draining out all the water within the pipes below where they exit with ease (it might take some time)
– Place a bucket underneath and remove any obstructions like toys or materials that may have fallen in
– Put a plunger on the toilets and push it down all around the rim of the toilet
– Push it back up for about 15 to 20 times. This will create enough suction for draining out all the water within the pipes below where they exit with ease (it might take some time)
– Flush again after doing everything mentioned above, and you should see a decrease in clogging problem!
The Best Ways for Preventing Clogs in Your Toilets and Drains
The Complete Guide to Preventing Clogs in Your Toilets and Drains
- Keep your toilets clean.
- Use a toilet brush at least once per week, or as soon as you notice problems with the toilets. If toilets are constantly clogged, this may be a sign of other problems. *
- Use the toilet plunger to clear toilets that are clogged in toilets with a water line, and use your hand or a rag for toilets without a waterline (e.g., dry toilets).
- Get rid of excess hair from toilets with a water line (e.g., toilets that have a waterline). Hair can get stuck to the sides of toilets and create clogs, or it will just swirl in the toilet bowl and make for an unpleasant experience when flushing.
- Flush toilets from left to right if possible; this will help to avoid toilets clogging in toilets with a waterline.
- Keep your toilet lids down when not using the toilets (e.g., after flushing). This will prevent dust from getting into the toilets and create blockages.
- Prevent significant amounts of liquids from getting into toilets. If you just need to rinse off a spoon, instead of dumping it in the toilets and flushing, pour it down the kitchen drain or outside through a strainer).
- Put toilet plungers away when not using them (e.g., after use), as this will prevent children from accessing them and create blockages.
- Avoid using plungers on toilets with a waterline, as this can damage the toilets (e.g., if you use it too forcefully).
- If toilets are constantly clogged or smelly, call an expert to diagnose toilet problems.
- If toilets are constantly clogged or smelly, call an expert to diagnose toilet problems.
- Avoid the temptation of overusing toilet plungers in toilets with a waterline (e.g., toilets that use pumps). This will damage your toilets and can lead to leaks if you do not know how much force is too forceful when using them on toilets with a waterline; this problem has been known to incur expensive repairs for some homeowners without insurance coverage.